What this page proposes
The open spec says a place can be a palm-size tile, that it has a tap tag, and that it may hold a swappable puck. It leaves the dimensions and the way a puck seats undecided.
This page fills those gaps with one set of numbers so that there is something to print and argue with. Every number here is a v0.1 proposal. It does not change the spec.
In The Shelf sketch the puck sits under the stone. Here it drops in from the top, so the tile prints without supports and a sensing puck can see the room.
See it
The tile with the blank puck in its bay, seen from above.
Drag to turn it. With a keyboard, select the drawing and use the arrow keys. It is drawn in your browser from the same triangles that are in the files, 6,580 of them, rounded to a thousandth of a millimetre.
The parts and the files
- Part 1
Place tile
The place itself. A ring on top marks where a piece lands, and the recess for the tag is under the middle of that ring. Beside it is a round bay with a hole through it for a puck. Four small feet.
100 × 100 × 9.2 mm. 2,720 triangles, 133 KB. Prints: top face down. The feet and the tag recess face up while it prints.
- Part 2
Blank puck
Fills the bay of a place that does no sensing. A place with no puck at all is still a place.
46 × 46 × 6.3 mm. 764 triangles, 37 KB. Prints: chamfered side down.
- Part 3 · optional
Sensing puck shell
Optional and untested. A cup that fits the same bay, with room inside for a small board.
46 × 46 × 24 mm. 956 triangles, 47 KB. Prints: chamfered side down, open end up.
- Part 4 · optional
Vented lid
Optional and untested. Pushes onto the shell. Slots let air and light in.
46 × 46 × 4.5 mm. 2,140 triangles, 105 KB. Prints: flat face down, lip up.
The files are binary STL in millimetres, and each one sits the way it prints. They are written by one script with no dependencies from one file of numbers, so anyone with Node can change a number and make them again: node scripts/baby-bonfire/first-place.mjs.
Putting it together
- Print the tile and the blank puck. Neither needs supports.
- Turn the tile feet up. Press a round 25 mm tag sticker into the shallow recess, in the middle.
- Turn the tile over onto its feet. The ring on top is now directly above the tag. That ring is where a piece lands.
- Drop the puck into the bay, chamfered side down. It should stand about 1 mm proud of the tile and turn freely. To take it out, lift the tile and push the puck up from below.
- Tap a phone on the ring to see whether it reads the tag through the tile. Nobody has tried this yet.
That is the whole of this first place: a marked spot with a tag, and a seat for a puck. It needs no power.
Printing: starting points
- Material. PLA or PETG. PETG holds its shape to a higher temperature. Neither belongs near heat.
- Settings. A 0.4 mm nozzle, 0.2 mm layers, three walls, four solid layers top and bottom, 15% infill. Use the temperatures printed on your spool.
- No supports, no brim. Sitting the way the files sit, no face overhangs by more than 45° and nothing bridges.
- The tile prints top face down. Its top takes the finish of your print bed. The chamfer round that face gives the first layer somewhere to spread.
- Bed. The tile is 100 mm square and each puck part is 46 mm across, so all four parts fit together on a 180 mm bed.
- Fit. The puck has 0.3 mm of room on each side in the bay, and the lid's lip has 0.15 mm in the shell. Printers differ. If a part is tight or loose, change
bay.clearanceorlid.lipClearanceand make the files again. - These are starting points. No slicer has been run on the files, so print time and the weight of plastic are not known. Printed solid, the tile would be 66 cm³ of plastic; with infill it will be less.
The tap tag
The recess under the tile is 26.6 mm across and 0.6 mm deep, made for a round 25 mm NFC sticker.
- Stickers. Round NFC stickers are on sale at 22 mm and 25 mm across. One 25 mm sticker is listed as 0.28 mm thick with a 22 mm antenna, and one 22 mm sticker as about 0.14 mm thick. A 30 mm one is listed too, with a note that it has been discontinued. For another size, change
tagRecess.stickerDiameter. - Chip. All three carry NXP's NTAG213. NXP sells the family as NTAG 213, 215 and 216, with 144, 504 or 888 bytes that a user can write, and says the chips follow the NFC Forum Type 2 Tag and ISO/IEC 14443 Type A specifications.
- Range. NXP gives an operating distance of up to 100 mm, depending on the reader's field and the antenna. That is not a promise about a phone and a small sticker. Here the tag sits under 7.4 mm of printed plastic. Whether a phone reads it from above is not tested. From below there is nothing in the way.
- Metal. Both sticker sellers say these tags do not work on metal. On a metal shelf this tag would sit about 1.5 mm above the metal and may not read. Not tested.
- Heat. The 25 mm sticker is rated from −25 °C to 70 °C. One more reason this place stays away from flame.
- What goes on the tag is not decided. The open spec says a tag lets a piece and a place tell which is which, and stops there.
Every dimension v0.1 proposal
All the numbers live in one file, params.json. Change one, run the script, and the files, these tables and the drawing above all follow. The open spec still lists dimensions as undecided, and nothing here changes that.
| Dimension | Value |
|---|---|
| Tile | |
Side of the square tiletile.size | 100 |
Corner radiustile.cornerRadius | 12 |
Thickness of the body, feet not countedtile.bodyHeight | 8 |
Chamfer round the top edgetile.topChamfer | 1.2 |
Chamfer round the bottom edgetile.bottomChamfer | 0.8 |
| Puck bay | |
Centre of the bay, to the right of the middle of the tilebay.x | 20 |
Centre of the bay, towards the backbay.y | 20 |
Gap between puck and bay, on each sidebay.clearance | 0.3 |
Chamfer round the mouth of the baybay.leadIn | 0.5 |
From the top face down to where the seat startsbay.wallDepth | 3.5 |
| Landing ring | |
Centre of the ring, to the right of the middle (minus is left)landing.x | −20 |
Centre of the ring, towards the back (minus is front)landing.y | −20 |
Across the ring, to the middle of its groovelanding.ringDiameter | 46.4 |
Width of the V groovelanding.grooveWidth | 1.2 |
Depth of the V groovelanding.grooveDepth | 0.6 |
| Tag recess, underneath | |
Centre of the recess, measured like the ringtagRecess.x | −20 |
Centre of the recess, measured like the ringtagRecess.y | −20 |
Sticker the recess is made fortagRecess.stickerDiameter | 25 |
Thickness of that sticker, from its sellertagRecess.stickerThickness | 0.28 |
Room round the sticker, on each sidetagRecess.clearance | 0.8 |
Depth of the recesstagRecess.depth | 0.6 |
| Feet | |
Centre of each foot, in from the two nearest edgesfeet.inset | 9 |
Across a foot where it joins the tilefeet.diameter | 9 |
Height of a footfeet.height | 1.2 |
How much a foot narrows on each side (equal to its height gives 45°)feet.taper | 1.2 |
| Pucks | |
Across any puckpuck.diameter | 46 |
Chamfer a puck sits on, the same on the puck and in the baypuck.seatChamfer | 1.5 |
Chamfer round the top of the blank puckpuck.topChamfer | 0.6 |
Height of the blank puckpuck.blankHeight | 6.3 |
| Sensing puck shell | |
Height of the shell, lid not countedshell.height | 24 |
Side wallshell.wall | 2 |
Floorshell.floor | 2.4 |
Largest board the cavity is sized forshell.largestBoard | 29 × 28 |
| Vented lid | |
Platelid.thickness | 2 |
Chamfer round the top edgelid.topChamfer | 0.6 |
How far the lip reaches into the shelllid.lipHeight | 2.5 |
Thickness of the liplid.lipWall | 2 |
Gap between lip and shell, on each sidelid.lipClearance | 0.15 |
Chamfer on the tip of the liplid.lipLeadIn | 0.4 |
Number of slotslid.vents | 8 |
Width of a slotlid.ventWidth | 2.4 |
Inner end of a slot, from the centrelid.ventInner | 6.5 |
Outer end of a slot, from the centrelid.ventOuter | 15 |
| How round things are drawn: segments, not mm | |
Round the bay, the ring and the pucksmesh.roundSegments | 96 |
Round the tag recessmesh.smallSegments | 64 |
Round each footmesh.footSegments | 32 |
Round each corner of the tilemesh.cornerSegments | 12 |
Round each end of a slotmesh.ventEndSegments | 8 |
What follows from those numbers
| Height of the tile standing on its feet | 9.2 |
|---|---|
| Across the bay | 46.6 |
| Across the mouth of the bay, at the top face | 47.6 |
| Across the hole below the seat | 43.6 |
| Bottom of the seat, below the top face | 5 |
| Underside of a seated puck, below the top face | 5.3 |
| Blank puck stands above the top face by | 1 |
| Largest round base that stays on the tile and clear of a puck | 60 |
| Across the tag recess | 26.6 |
| Plastic between the tag and the top face | 7.4 |
| Tag above the table, with the tile on its feet | 1.5 |
| Across a foot where it meets the table | 6.6 |
| Across the cavity of the shell | 42 |
| Depth of the cavity | 21.6 |
| Room at each corner of the largest board, lying flat in the cavity | 0.84 |
| Across the lip of the lid, outside | 41.7 |
| Across the lip of the lid, inside | 37.7 |
| Height of the lid, lip included | 4.5 |
| Sensing puck with its lid stands above the top face by | 20.7 |
How thick the plastic is
| Tile, rim between the bay and the edge of the top face | 5 |
|---|---|
| Tile, plastic between the tag and the top face | 7.4 |
| Tile, straight wall of the hole below the seat | 3 |
| Sensing puck shell, side wall | 2 |
| Sensing puck shell, floor | 2.4 |
| Sensing puck shell, floor corner to the seat chamfer | 2.05 |
| Lid, plate | 2 |
| Lid, lip | 2 |
| Lid, tip of the lip (thinnest) | 1.6 |
| Lid, bar between two vents | 2.57 |
| Lid, between a vent and the lip | 2.65 |
Optional: a puck that senses Untested
The open spec says the puck is the part that senses, and that the first one senses heat and light. This is a sketch of one way to try that with parts on sale today: a shell and a vented lid that fit the same bay, four parts to go inside, and how they might be wired.
None of it has been built, and there is no firmware, so nothing here sends a signal yet. A place does not need it. The tile, a blank puck and a tag are complete with nothing plugged in.
Parts, by type
- A small low-power board with Bluetooth LE
Seeed Studio XIAO nRF52840
Seeed gives its size as 21 × 17.8 mm and its standby draw as 5 μA. It carries a charging chip for a rechargeable lithium battery.
Use the plain board. Seeed's “Sense” version of it adds a microphone and a motion sensor, and the open spec allows no microphones.
Listed on Seeed's own shop on Nov 11, 2026. Its stock line could not be read: not verified.
- A temperature and humidity sensor
Adafruit SHT40 breakout, product 4885
In stock on Nov 11, 2026. Adafruit gives the board's supply as 3.3 to 5 V, its typical accuracy as ±0.2 °C and ±1.8% relative humidity, and its I2C address as 0x44.
Board size: not on the product page, not verified.
- An ambient light sensor
Adafruit VEML7700 lux sensor, product 4162
In stock on Nov 11, 2026. Adafruit describes a range from 0 to about 120,000 lux, and a 3.3 V regulator on the board so that it runs from 3.3 V or 5 V.
Board size: not on the product page, not verified.
- A coin-cell holder
Adafruit 20 mm coin cell breakout with on-off switch, product 1871
In stock on Nov 11, 2026. Adafruit gives its size as 29 × 28 mm. It holds one CR2032 cell, which is not included, and has a power pin that goes through the switch.
That switch is the physical off that the open spec asks of every networked object.
No prices are given. Each page was opened on Nov 11, 2026; check it again before ordering.
Wiring sketch
Known doubts about this sketch
- Power. Seeed describes two ways to power the board: 5 V through its USB-C socket, or a 3.7 V lithium battery on its battery pads, which the board then charges. Its wiki calls the 3V3 pin a power output. This sketch feeds a coin cell into that pin instead. Seeed's pages do not describe doing so, and it has not been tried.
- Keep the cell away from the charger. A CR2032 is not a rechargeable cell. Do not wire it to the board's battery pads, and switch it off before plugging in USB.
- Voltage. Adafruit describes a CR2032 as 3 V nominal with about 220 mAh. Its humidity board asks for 3.3 to 5 V and its light board carries a 3.3 V regulator, so on a coin cell both sit below the supply they are described for. They may work. Nobody has checked, and nobody has measured how long a cell would last.
- Room. The shell's cavity is 42 mm across and 21.6 mm deep. The width was chosen so the 29 × 28 mm cell board lies flat with 0.84 mm to spare at each corner. The depth is a guess: the sellers' pages do not give the height of any of the four parts.
- Sensing through slots. The lid has 8 slots for air and light. How well a sensor behind them reads a room is unknown.
- Reaching the switch. The switch ends up inside the shell, under the lid. A physical off should be something a person can see and reach, so a later shell needs an opening for it.
- The radio is not settled. Bluetooth LE is here because small boards that have it are easy to buy. The open mesh notes still list the radio as an open question, and the spec's rule stands: every networked object has a physical off and is off by default.
How the shapes were checked
The script that writes the files checks each part as it builds it: every edge is shared by exactly two triangles, no triangle is empty, and the surface encloses a volume. A second script, in Python and sharing no code with the first, then reads the finished files. On Nov 11, 2026 it reported, for all four parts:
- each mesh is watertight, wound one way and a single body;
- each bounding box matches params.json;
- each volume matches a calculation done by hand from params.json, to better than one part in ten thousand;
- of 40,000 random points per part, every one well inside the described shape is inside the mesh and every one well outside is outside, so the bay, the ring, the recess and the feet are where the tables put them;
- sitting the way it prints, no face overhangs by more than 45°;
- going straight in from every triangle, the shortest path through plastic is 2.0 mm.
None of that says the parts print well, fit each other or last. Only a printer can say that.
What nobody knows yet
- Whether it prints cleanly, on any printer.
- Whether the puck drops in and lifts out, and whether the lid pushes on, at the gaps given.
- Whether the tile sits flat on its four feet.
- Whether a phone reads the tag through the tile, and what a phone does when a tagged piece sits on the ring right over the tile's own tag.
- Everything about the sensing puck.
- Whether 100 mm is the right size for a place, 46 mm the right puck, or a bay open at the top the right way for a puck to seat. The open spec lists all three as undecided.
Sources
Each page below was opened on Nov 11, 2026. What it says is put in this page's own words.
- Polymaker, PolyLite PLA technical data sheet V5.4Glass transition 61 °C, Vicat softening temperature 63 °C.
- Polymaker, PolyLite PETG technical data sheet V5.4Glass transition 81 °C, Vicat softening temperature 84 °C.
- Prusa Knowledge Base, PLAPLA softens and deforms above 60 °C.
- Prusa Knowledge Base, PETGPETG parts suit use below 80 °C.
- NXP, NTAG 213/215/216The chip family, its memory sizes, the specifications it follows, operating distance.
- GoToTags, NFC label NTAG213, 25 mm round25 mm across, 0.28 mm thick, 22 mm antenna, not for metal, −25 to 70 °C, normally stocked.
- Shop NFC, NFC stickers NTAG213, 22 mm round22 mm across, 20 mm antenna, 136 μm thick, not for metal, in stock. The address still says 25 mm; the page is for the 22 mm sticker.
- GoToTags, NFC label NTAG213, 30 mm round30 mm across, 25 mm antenna. The page says it has been discontinued.
- Seeed Studio, XIAO nRF52840 product pageSize, standby draw, battery charging, what the Sense version adds.
- Seeed Studio wiki, getting started with the XIAO nRF52840D4 is I2C data and D5 is I2C clock; the 3V3 pin is a power output; the charging chip.
- Adafruit, SHT40 temperature and humidity sensor, product 4885Supply, accuracy, I2C address, in stock.
- Adafruit, VEML7700 lux sensor, product 4162Range, regulator, in stock.
- Adafruit, 20 mm coin cell breakout with on-off switch, product 187129 × 28 mm, switched power pin, in stock.
- Adafruit, CR2032 coin cell holder with switch, product 4856A CR2032 is 3 V nominal with about 220 mAh.
Not verified Whether Seeed has the board in stock. The size of the two sensor boards. The height of all four electronic parts. Whether a coin cell can run the board through its 3V3 pin. How far away a phone reads the tag. Every one of these is marked where it comes up.
Send a correction or a photo
If you print one, or see something wrong on this page, please say so. A report that says “this did not fit” is as useful as one that says it did.
Open an issue Write to hello@pointcast.xyz
- If you use GitHub, open an issue, or a pull request that changes params.json.
- If you do not, write to hello@pointcast.xyz with “Baby Bonfire” in the subject.
- Say which printer and which plastic, what fitted and what did not, and whether a phone read the tag. A photo helps.
The make a piece page says what every contribution keeps to, and that nothing is merged or published without Mike Hoydich's say.